Here are minutes of our telecon on Tuesday Aug. 8, my apologies for the delay! -- as well as work done since then -- please just reply with (or let me know) any corrections -- thanks! :
Attendees: Arnold Gaertner (NRC) & me
The telemetry issues all finally seem to be essentially solved: Alexy and I got rock-solid transmission between Mt. Doug and UVic on each of two different frequencies (the DNT's at 910 MHz and the SHX1's at 144 MHz) on a test. We still do need to do a combined test of both telemetry and telescope tracking between UVic and the DAO, but that should be essentially the last major hurdle in that regard. The new Yagi for 144 (and 440) MHz arrived, and I mounted it on a combined tip-tilt mount on the Deneb ground station together with the large 910 MHz Yagi antenna:
http://projectaltair.org/HyperNews/get/AUX/2017/08/21/19.38-13193-enebWithVHFUHFAntenna.jpg
The ALTAIR payload is also now successfully communicating, via both its 910 MHz DNT and 144 MHz SHX1, with the Capella ground station. The next step in that work sequence is to add the GPS mast to the top of the ALTAIR gondola and transmit that information. But before making that addition to the top of the gondola shell, I refitted the bottom shell to accommodate the things (i.e. the shock-absorbing wheels and the ultrasonic distance sensors) that had earlier been added to the bottom interior. That involved making a new bottom shell with wheel wells:
http://projectaltair.org/HyperNews/get/AUX/2017/08/21/19.38-73259-WheelWells.jpg
and then accommodating the integrating sphere output port (as well as the ultrasonic distance sensors):
http://projectaltair.org/HyperNews/get/AUX/2017/08/21/19.38-13704-FullBottomShell.jpg
There was a bit of non-eclipse-related excitement today, as when I placed the payload on the wood-and-aluminum plank for outdoor GPS testing that I had pop-riveted a few months ago to the aluminum exterior window frame of my office (and then attached the payload to the plank and frame with some new carabiners), the entire exterior window frame came off (nearly taking the payload with it)! Fortunately I had tied two of my carabiners to the fixed interior window frame, so I ended up hanging on to the payload and exterior frame, out my window. It turns out I had pop-riveted to a section of the exterior frame that is (there was no good way to tell this) not intended to be load-bearing -- the load-bearing bolts were underneath that section of the frame. Anyway, I fixed that (by re-mounting the outdoor plank to the load-bearing bolts), and it now appears to support the payload quite nicely:
http://projectaltair.org/HyperNews/get/AUX/2017/08/21/19.38-81230-utdoorPlankForTesting.jpg
Students Alexy Decrooq and Kyle Jordan, as well as software expert Layth Holubeshen, are all working on getting the code that runs the balloon flight path predictor running inside of AIFCOMSS:
http://projectaltair.org/HyperNews/get/AUX/2017/07/10/18.55-39312-IFCOMSSwithPredictor1.png http://projectaltair.org/HyperNews/get/AUX/2017/07/10/18.55-56749-IFCOMSSwithPredictor2.png
into good shape such that it is easier to install, and additionally working on relatively easy and reproducible instructions on how to install it (on Windows, Mac, and Linux platforms). We're greatly looking forward to adding those instructions as a README at https://github.com/ProjectALTAIR/AIFCOMSSwithCUPredictorTest, as well as making any changes to the code itself to make it easier to install. After that's done, we will work on updating and improving the flight prediction code itself -- and also, after that, seeing if we can successfully simulate some form of station-keeping over a region of land, using the actual wind forecasts and data from NOAA, and also reasonable values for drag, propulsive thrust, battery power (as well as some battery recharging with future lightweight solar panels), etc etc.
Machinist Chris Secord has been very busy welding the 12" diameter aluminum sphere that will function as our pre- and post-flight photometry cross-check device, and here's the result of his work:
http://projectaltair.org/HyperNews/get/AUX/2017/08/21/19.38-86577-WeldedSphere.jpg
He still needs to tack-weld the bottom support ring onto the bottom half of the sphere. When he finishes this weld job, we'll then prime the interior with white powder coat, and then use our Avian-B paint to paint over the powder coat (Avian-B sticks far better over a powder coat than directly on aluminum, since Avian-B does not contain etch primer). The sphere should be coated and completed in the next couple of weeks.
ALTAIR-Victoria is fully assembled, and its light sources are functioning nominally:
http://projectaltair.org/HyperNews/get/AUX/2017/06/26/19.25-55880-ALTAIRwithGear.JPG
however: only the light sources themselves, plus the basic telemetry, have been tested so far -- they both need to be tested in concert with the photodiode readout; with the orientation, GPS, and environmental monitoring; with the onboard data storage; with the propulsion and its monitoring data; etc., etc., etc. Much of the software to combine all that functionality, and resultantly _very_ large number of possible error conditions, still needs to be written. Thus, there remains an enormous amount to do -- including, of course, drop testing, more long-range telemetry testing, etc. -- before seriously thinking about a flight ...
Mark Lenckowski has completed the stabilized pole for the new 10-meter-high drop test setup at Victoria:
http://projectaltair.org/HyperNews/get/AUX/2016/12/19/15.28-91194-MeterStabilizedPole_1.jpg http://projectaltair.org/HyperNews/get/AUX/2016/12/19/15.28-81425-MeterStabilizedPole_2.jpg
As you can see (faintly), he affixed side-struts and guy wire to the PVC pole, to prevent it from bending in either of the two transverse directions, so it can now be raised to vertical, from horizontal, without bending or breaking.
The survey-tripod-mounted device to cross-check yaw-pitch-roll information from the gondola (e.g., on days before/after flights) is constructed now, thanks to Mark Lenckowski -- photo at:
http://projectaltair.org/HyperNews/get/AUX/2016/08/31/18.15-24048-wPitchRollCalibDevice.jpg
and all that remains to be done is to finish the small fitting between the device and the bottom of the payload. The purchased hardware in it includes both the survey tripod (http://www.cpotools.com/cst-berger-60-alwi20-o-aluminum-tripod-with-quick-release--orange-/cstn60-alwi20-o,default,pd.html), two adjustable angle mounts (http://www.thorlabs.com/thorproduct.cfm?partnumber=AP180), and a rotation mount (https://www.thorlabs.com/thorproduct.cfm?partnumber=RP01). That last fitting to attach (temporarily, pre- or post-flight) the upper adjustable angle mount to the payload feet has been started and will be completed here in the next couple weeks.
We're currently revising the draft initial contractual agreement from our colleagues at Globalstar Canada regarding 2 initial SPOT Trace devices (and their service plans) for the educational side-project for the upcoming NATO SPS application, in which classrooms in elementary and high schools could launch company-donated SPOT Traces using party balloons (or a more environmentally-friendly version thereof), and track them to learn more about winds at different levels in Earth's atmosphere.
Another next step, software-wise, is to add more data information to the telemetry communication between ALTAIR-Victoria:
http://projectaltair.org/HyperNews/get/AUX/2017/04/17/18.41-75359-assembledpayload1.JPG
and the Capella ground station:
http://projectaltair.org/HyperNews/get/AUX/2017/01/23/21.17-37945-Capella.jpg
and to update the control and monitoring software to incorporate the telemetered info, and also implement onboard SD card data storage, as well as storage of the telemetered info.
Houman will send Cordell and/or us updated sections of his master's thesis soon -- that information will be extremely useful to us going forward. Also, Susana and Nathan, it would be very helpful for us all to get the JHU students' final writeup when you have a chance.
Our next grant application will be a NATO "Science for Peace and Security" application, together with Australian colleague partners.
That's all I remember, please send things that I forgot. Next telecon tomorrow, at the usual 4:00 pm Eastern time.
Cheers, talk to you all tomorrow! justin
On Mon, 07 Aug 2017 22:48:22 GMT, Justin Albert wrote:
> Hi! > > Telecon tomorrow (Aug. 8 in North America, Aug. 9 in Australia) at the > regular time: 4:00 pm Eastern (1:00 pm Pacific, 10 am Hawaii, 22.00 > European, 6 am Eastern Australia). Discussion items include: > flight/telescope plans and tests; construction, drop testing, and other > tests of the new gondolas/payloads; light sources and light source > modelling; goniometric and pre- and post-flight calibration; propulsion > work; nanosat bus and payload solid models; computing/website; grant > applications; and recap of schedules. > > Here's how to connect: > > 1) Open Skype on your computer (note that of course, you should first install Skype, http://www.skype.com , on your machine if you haven't already). > 2) In the "Contacts" menu, add me ( jalbertuvic ) as a contact, if you haven't already. > 3) Just wait for me to Skype-call you at the usual time (4 pm Eastern, 1 pm Pacific). > 4) If there is any trouble, or if you don't get a Skype-call for some reason and would like to join, just send me an e-mail (jalbert@uvic.ca). > > Here's the tentative agenda: > > I) Flight & telescope plans, and upcoming tests > II) Construction, drop tests, and other forms of tests of the new gondolas and payloads here in Victoria. > III) Diffused light source, and its modelling, pre- and post-flight calibration, and goniometric calibrations > IV) Nanosat solid models & Houman's thesis > V) Computing/website, including new flight control and simulation progress. > VI) Grant applications > VII) AOB > > Talk to you all tomorrow, thanks! > justin
Attachments:
http://projectaltair.org/HyperNews/get/AUX/2016/05/22/18.23-24702-12inAlSphere.jpg
http://projectaltair.org/HyperNews/get/AUX/2016/04/06/16.53-58615-SideView.pdf
http://projectaltair.org/HyperNews/get/AUX/2016/04/06/16.53-48539-TopView.pdf
http://projectaltair.org/HyperNews/get/AUX/2017/06/26/19.25-55880-ALTAIRwithGear.JPG
http://projectaltair.org/HyperNews/get/AUX/2016/08/17/20.30-99000-AvianBTestHemisphere.jpg
http://projectaltair.org/HyperNews/get/AUX/2016/08/17/20.30-68004-Betelgeuse1.jpg
http://projectaltair.org/HyperNews/get/AUX/2016/08/17/20.30-53104-Betelgeuse2.jpg
